Essential Woodworking Tools for Beginners

Want create site? Find Free WordPress Themes and plugins.

Essential Woodworking Tools for Beginners. Want to Buy A Table Saw? Know Your Glossary of Woodworking Terms

The following is a glossary list of common definitions, terms and phrases used as they relate to table saws and woodworking in general.

If you’re interested in buying a table saw, become familiar with these woodworking terms for understanding features, assembling, adjusting or operating your table saw.

Anti-Kickback Pawls (radial arm and table saws)

A device which, when properly installed and maintained, is designed to stop the workpiece from being kicked back toward the front of the saw during a ripping operation.

Arbor

A metal shaft extending from the drives implement that is the mounting location for the saw blade.

Bevel Cut

A cutting operating make with the blade at any angle other than 90° to the table surfaces.

Blade Guard Assembly

Metal or plastic protection device that mounts over the saw blade. Its function is to intercept the operator from coming into contact with the saw blade.

Compound Cut

A cross cut made with both a miter and a bevel angle.

Cross Cut

A cutting or shaping operation make across the grain or the width of the workpiece.

Cutter head (planers and jointer planers)

A rotating cutterhead with adjustable blades or knives. The blades or knives remove material from the workpiece.

Dado Blade

Blade or set of blades that are used to cut grooves and rabbets.

Dado Cut

Cutting operation that use a dado blade to cut a flat bottomed groove into the faces of the workpiece.

Feather board

Safety device used to keep the workpiece against the rip fence and against the table surface.

FPM or SPM

Feet per minute (or strokes per minute), used in reference to blade movement.

Freehand

Performing a cut unaccompanied by the work piece being guided by a fence, miter gauge, or other aids.

Gum

A sticky, sap-based residue from wood products.

Heel

Alignment of the blade to the fence.

Kerf

The resulting cut or gap in the workpiece after the saw blade passes through during a cutting operation.

Kickback

An event in which the workpiece is propelled back towards the operator at a high rate of speed.

Miter Cut

A cutting operations build with the workpiece at any angle to the blade other than 90°.

Non-Through Cut

A cut in which the blade does not cut through the thickness of the workpiece.

Parallel

Being an equal distance apart at every point along two given lines or planes (i.e. the rip fence face is collateral to the face of the saw blade).

Perpendicular

Lines or planes that intersect and form right-angles (i.e. the blade is perpendicular to the table surface).

Pilot Hole (drill presses)

A small hole drilled in a workpiece that serves as a guide for drilling widely holes accurately.

Push Blocks (for table saws)

Device used to hold the workpiece during cutting operations. This aid supported keep the operator’s hands well away from the blade. Visit for the push block reviews.

Essential Woodworking Tools for BeginnersPush Stick

Safety device used to push the workpiece through a cutting operation. Used most often when rip cutting thin workpieces. The aid helps repose the operator’s hands well away from the blade.

Rabbet

Cutting operation that creates an L-shaped channel along the edge of the workpiece.

Resaw

A cutting operation to shorten the thickness of the work piece to make thinner pieces.

Resin

A sticky, sap-based substance that has hardened.

Revolutions Per Minute (RPM)

The figure of turns completed by a spinning object in one minute.

Rip Cut

Cutting operation in which the rip fence is used to cut across the length of the workpiece.

Riving Knife/Spreader/Splitter

Metal plate located behind the blade. It sustains the kerf opening in the wood when performing a cutting operation.

Saw Blade Path

The place over, under, behind, or in front of the blade. As it applies to the workpiece, that area which will be or has been cut by the blade.

Set

The distances that the tip of the saw blades tooth is bent (or set) outward from the face of the blade.

Snipe (planers)

Depressions made at either end of a workpiece by cutter blades when the workpiece is not properly supported.

Straightedge

A tool used to check the flatness, parallelism, or consistency of a surface(s).

Thin Kerf Blade

A blade with a kerf or depth that is thinner than a standard blade. Click Here for more information.

Through Cut

A cut in which the blade cuts completely through the thickness of the workpiece.

Throw-Back

The throwing back of a workpiece usually caused by the workpiece being dropped into the blade or being placed inadvertently in contact with the blade.

Workpiece or Material

The item on which the operation is being done.

Worktable

Surfaces where the workpiece material rests while performing a cutting, drilling, planing, or sanding operation.

I hope you found this post helpful. For a wide range of reviews visit: table saw reviews.

Did you find apk for android? You can find new Free Android Games and apps.

We will be happy to hear your thoughts

      Leave a reply